SPCMAKER 220AR 220MM Brushless FPV Racing Drone BNF Version RunCam Swift 2 Omnibus F4 flight controller 30A BLheli_s ESC (2-6S LiPo)
We use cookies to improve your online experience. By continuing browsing this website, we assume you agree our use of cookies.
Your position: Home / Racing Drone / BNF

SPCMAKER 220AR 220MM Brushless FPV Racing Drone BNF Version RunCam Swift 2 Omnibus F4 flight controller 30A BLheli_s ESC (2-6S LiPo)

    Please select the information you wantX
  • Voltage:
  • Model:
(998 available)
Shipping Cost:
Estimated Delivery Time:
Please select the country you want to ship from
  • Description
  • Reviews

Brand name: SPC Maker
Product model: SPC 220AR
Wheelbase: 220mm
Size: 187mm*187mm*40mm
Weight: 325g (without battery)
Flight weight: 485g(Include battery)
Motor: 2205KV2300 brushless motor
ESC: 30A BLheli_s ESC (2-6S LiPo)
Propeller: 5 inches 3-blades propeller
Receiver: Receiver: Frsky/DSMX/Flysky/Futaba(optional)
Camera: RunCam Swift 2 1/3 "600TVL FPV camera 2.3mm lens CCD camera
VTX: 5.8g 25MW-300MW 40CH Video transmitter
Flight controller: Omnibus F4
OSD: Betaflight OSD
Firmware of flight controller: betaflight_3.1.7
Flight time: 5 minutes
Buzzer Ready
Battery: 14.8V 1300mAh 120C lipo battery
Packing weight: 735g
Packing size: 245*245*75mm
Ominibus F4 flight controller
Input:2-4 Cell LiPo
-STM32 F405 Flihgt Control Board integrated with PDB
-MPU6000 6 axis SPI Gyro & Accelerometer
-Dshot support
-Drag and Drop OSD configured via Betaflight Configurator
-SBUS/PPM AND Spketrum dsm-x Ports
-On-board Video Filter(only can supply 5V to VTX and Camera)
input voltage: 2-6 lithium batteries
Sustained current: 30 a.
Maximum current: 40 a 10 seconds or more
Size: 14.8 x29x5mm
Weight: 7.9 g
Application: BLHeli_S
Drive types: independent half bridge driver chip + N channel MOS tube, support OneShot125 OneShot42, MultiShot, Dshot150, Dshot300, Dshot600
5.8G 25mW/300mW 40CH 5645-5945MHz VTX
Input voltage: 7.4-24v
Current: 210 ma / 12 v @ 300 mw
Power: 0/25 mw / 300 mw
Frequency range: 40CH/ 5645mhz-5945mhz
Setup: button + digital tube
Output voltage: 5V@1.2A
Size: 36 x36x8mm
Mounting hole distance: 30.5mm
Model : RunCam Swift 2
Image Sensor: 1/3" SONY Super HAD II CCD
Horizontal Resolution: 600TVL
Lens:2.3mm /150°
Signal System:NTSC
S/N Ratio:>60dB (AGC OFF)
Electronic Shutter Speed :1/60~100,000
Auto Gain Control (AGC) :Yes
Back Light Compensation (BLC):Yes
Min. Illumination:0.01Lux@1.2F
Power:DC 5-36V
Net Weight:14g
1.DSM2 Receiver Support Spectrum/JR(DSM2 protocol) DEVO10/DEVO 7E(with deviation firmware).
2.Frsky Receiver Support FRSKY taranis X9D/X9D PLUS(D16 mode),and XJT (D16 Mode),DJT DFT DHT Transmitter.
3.Flysky Receiver Support FS-I6FS-I6X.FS-I6S.FS-TM8.FS-TM10.FS-I10 and other second-generation AFHDS 2A protocol remote control
4.Futaba Receiver Support  TM7,TM8, TM10, TM14 T6EX-2.4G,7C-2.4G,T8FG,T10CG ,T12FG.T14SG.
Receiver Setup and Binding Methods
Quads with DSM Compatible Receivers
Binding method for Spektrum radios:
Pair code: (for code, not external battery)
1. The receiver for the Cleanflight, Betaflight firmware flight control, you can enter the CLI command line
2. (set spektrum_sat_bind = 9 )carriage return,
3. In the input (save) carriage return.
4. Disconnect the USB cable, re-power to the flight control, the receiver orange indicator light will flash, said the receiver into the code waiting mode.
5. Open the remote control, the remote control into the code mode, the success of the code, the orange light is always bright, no signal, orange light off.
Quads with FrSky Receivers
Binding with FrSky Taranis X9D Plus Transmitter
1.Turn on your Taranis X9D Plus transmitter,goto“Model Setup”(Press MENU and PAGE button once).In the“Internal FR”section,choose Mode=D16,Channel Range=CH1-16,Receiver No.01,and then click“Bind”,the transmitter will start beeping.
2.Power up the XM+ receiver while holding the F/S buttn(aka.Bind button).The LED on the receiver will start flashing,that means binding has completed.
3.Power off Transmitter and Receiver
4.Turn on the transmitter and power on the Receiver,you should see the Greed LED on the receiver,that means it has bound with your transmitter.
Quads with FlySky Receivers
Binding method for FlySky radios:
Support radios with the second generation protocol (AFHDS 2A).
1.Enter the binding mode in the radio.
2.Hold the binding button on receiver, and power it on. Rapid flash of LED indicates the receiver is in binding mode. If binding is successful, the LED light will change to slow flash.
3.Exit binding mode of the radio. The LED light on receiver should become solid, indicating completion of binding.
Enable s.Bus mode:
Output modes can be switched in lieu of normal communication between radio and receiver. Hold the binding button for 2 seconds to change to s.Bus mode. If LED light flashes rapidly two times and off for 1 second, then it is successfully changed to s.Bus output mode.
Quads with Futaba Compatible Receivers
Binding method for Futaba radios:
Compatible with Futaba radios support FASST.
1.Set the radio to FASST mode. Hold the binding button on receiver and then power it on. The red LED should flash rapidly. Release binding button the LED should flash red and green alternately, and then turns to solid green to indicate a successful binding. It may requires several trials to complete a binding. A solid red LED indicates the binding is not established.
2.Fail safe can be setup in the radio, and can be set after binding process. Hold the binding key for 2-3 seconds, the LED indicator of failsafe will flash rapidly and then turns to solid green, indicating it is in fail safe mode.
Package include:
1 x SPC Maker 220AR Frame
1 x Omnibus F4
1 x Frsky/DSMX/Flysky/futaba(optional receiver)
4 x 2205KV2300 brushless motor
4 x 30A  BLheli_s ESC (2-6S LiPo)
4 x 5 inches 3-blades propeller CW
4 x 5 inches 3-blades propeller CCW
1 x RunCam Swift 2 1/3 "600TVL FPV camera 2.3mm lens CCD camera
1 x 5.8G 25mW-300mW 40CH  VTX
2 x 14.8V 1300mAh 30C lipo battery (comes without charger)
1 x buzzer
4x3 * 100mm nylon band
1x20mm * 250mm magic band
2x35mm * 60mm back to back with 3M rubber magic belt

Average rating:
Share your thoughts with other customers
Write a review
Product reviews can be carried out after the member login, please click here to login
Links:adult doll